Showing results: 61 - 75 of 92 items found.
-
EX-F1 -
Panasonic Industrial Devices Sales Company of America
The EX-F1 Pipe-Mountable Liquid Level Detection Sensor can not only be easily mounted onto a pipe with just tying bands, but it requires minimal mounting space thanks to its' built-in amplifier and compact size. Positioning can also be easily changed with the release lever even after mounting.
-
M6 -
Seismic Source Co.
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
NP-2000 Series -
Ono Sokki
This sensor converts mechanical vibrations into electric signals in proportion of vibration acceleration.You can choose the one that is ideal for your purpose,conditions,applications etc. from wide variety of selection.Charge amplifier is necessary because it is a charge output type,however, compared to pre-amplifier built-in type, it can be used at higher temperature in general.
-
NaPiCa -
Panasonic Industrial Devices Sales Company of America
Visible light sensor (Silicon Photo IC) that detects light and converts into electrical current. Consists of a photodiode and built-in amplifier. Optical filter provides spectral response similar to human eye sensitivity. Applications include: LCD Backlight Control, Commercial and Residential Lighting Brightness Control, Security Lighting.
-
SPECTRA GT30 -
Ametek Power Instruments
The SpectraTM GT30 is easily mounted directly to the turbine case or on a short standoff pipe via a 3/4 inch NPT internal thread. The two-wire, 24 VDC loop-powered solid-state sensor is fully self-contained, therefore it does not require a separate amplifier. AMETEK offers various cabling options depending on the application.
-
FX-410 -
Panasonic Industrial Devices Sales Company of America
This dual display digital Fiber Sensor is unique with its manual threshold value setting. Just "Look" and "Turn" simple, easy-to-use Fiber amplifier. The incident light intensity and threshold values can be checked at the same time with operation needed. In addition, no complex mode settings are needed when the values are adjusted.
-
ES Series -
Keyence
Long-distance Separate-amplifier Proximity Sensors. Detecting distance twice that of conventional sensors. Detecting distance is easily adjustable. Wide range of sensor head types available. Built-in alarm output. Separate amplifier proximity sensors with twice the detecting distance of self-contained sensors and a range of up to 8-mm (shielded) and up to 70-mm (non-shielded).
-
McLAREN Applied Technologies
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
EX-Z -
Panasonic Industrial Devices Sales Company of America
At a thickness of 3mm, the EX-Z Series is one of the world's thinnest Photoelectric Sensors with a built-in amplifier which was achieved by utilizing a new Semiconductor packaging technology that does not use wire bonding. The compact design now makes it possible to install the sensors in narrow spaces that, in the past, could fit only a conventional fiber sensor head.
-
EX-30 Ver.2 -
Panasonic Industrial Devices Sales Company of America
With an M4 Thru-Beam Type and an M6 Reflective Type Sensor, the user has a series of Miniature Photoelectric Sensors at their disposal from Panasonic. In addition to being quick and easy to install, the EX-30 Series Sensors' integrated signal amplifier, stable mechanical properties, and robust, zinc housing make them attractive alternatives to Photoelectric Sensors with fiber cables.
-
HF03 / LI19 -
Hukseflux Thermal Sensors B.V.
The HF03 is a heat flux sensor that can be used in mobile applications. It is combined with LI19, a high accuracy hand-held read-out unit that can be used both for mobile measurements and as an amplifier directly connected to a PC. The combination HF03 / LI19 is typically used to study heat flux levels around flares and fires, and to calibrate flare radiation monitors / flare heat flux sensors.
-
X005 Series -
Positek Limited
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
Kistler Instrument Corp.
To get most out of high-quality sensors, accurate, low-noise processing of the sensor signals that are emitted is essential. Kistler offers an attractive portfolio of solutions for signal processing and subsequent data digitization. Piezoelectric (PE) sensors with a charge output require a so-called charge amplifier. On the other hand, piezoelectric sensors with integrated electronics (IEPE) are supplied by Piezotron couplers which decouple and amplify the signal.
-
mks Ophir
The OEM “standard” sensors are actually families of existing OEM sensors with typical specifications shown. They can be tailored as needed to fit your specific requirements. In addition to the products described, Ophir has developed hundreds of other OEM solutions. These compact laser power sensors have built-in amplifiers and are easy to install. They contain all the electronics needed including algorithms to increase the sensor's speed of response. Connections to the sensors are simple, with the host providing DC power and the sensor providing a voltage or digital output. Outputs Available: DB15 smart sensor output; Calibrated analog output; RS232; USB; Ehthernet. Simply fill out the Sensor Customization form so we can provide just the right solution for your needs.
-
UC9710xx -
UC Instruments, Corp.
The UC8710C, UC9710L and UC8710CL tunable laser modules offer superior performance in testing DWDM components, AWG & PLC components, and optical amplifiers, and performing other general- purpose fiber optical test and measurement applications particularly in fiber grating sensor fast sweep testing.